Fire Testing Equipments

Product Details:

UL-94 Flame Retardant Tester is used forthe flammability testing of plastic materialssuch as V-0 V-1 V-2, HB, 5V, HF-1 HF-2,HBF material or foam , and used inconsumer electric devices and appliancesfor flammability rating assessment. Such asinsulating housing of household appliances,switch panel, the printed circuit board andinsulating material etc.

Product Details:

The DNG Smoke Density Chamber, is considered to be one of the most widely used test equipment for the measurement of the smoke volume generated from the burning material, such as building material, non-metallic material in railway, marine, aeroplane.

Product Details:

The combustion chamber is made of stainless steel .The internal dimensions of the combustion chamber is 305mm x 451mm and long 7.6m with firebricks laying which has satisfactory insulation property.

Product Details:

Needle Flame tester specifies a needle-flame test to simulate the effect of a small flame which may result from fault conditions, in order to assess product and material's ignition risk and fire retardance by a simulation technique. A 12 mm high flame held at a 45° angle is applied to the base of a test specimen for a specified period. Tissue paper is laid out 200 mm beneath the test specimen (alternatively materials that would normally surround the test material in application may be laid out in place of tissue paper to measure the effect of the test material on surrounding materials).

Product Details:

The Cone Calorimeter is used for the determination of the fire behavior of the various samples in the solid state. This Device is used to collect information of the various parameters associated with the burning characteristics such as ignition time, mass loss, combustion products, heat release rate etc. of various samples. For the determination of Heat Release Rate, the Samples are exposed to the irradiative heat flux at the surface.

Product Details:

This part of IEC 60695 specifies small scale laboratory test procedure intended to compare the burning behaviour of different materials.

Product Details:

This Radiant Panel Flame Spread Test Apparatus is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions

Product Details:

THIS PART OF ISO 5658-2 specifies a method of test for measuring the lateral spread of flame along the surface of a specimen of a product orientated in the vertical position. It provides data suitable forcomparing the performance of essentially flat materials, composites or assemblies that are used primarily as the exposed surface of walls in buildings and vehicles, such as train and ships.

Product Details:

The Cone Calorimeter is used for the determination of the fire behavior of the various samples in the solid state. This Device is used to collect information of the various parameters associated with the burning characteristics such as ignition time, mass loss, combustion products, heat release rate etc. of various samples. For the determination of Heat Release Rate, the Samples are exposed to the irradiative heat flux at the surface.

Product Details:

The BS476-6 Fire Propagation test apparatus is used for determination of rate of growth of fire in a compartment. It gives Fire propagation Index and indices, which are used as critical parameters for Class O classification.

Product Details:

The NCD 1409 Toxicity Chamber is consist of an enclosure of about 1m³ volume. Inner wall has the lining of polypropylene to protect sticking nature of gaseous mixture and for easy cleaning option. Chamber is fitted with a forced air extraction system, which can be opened or closed through control panel when required. The chamber is fitted with airtight sampling port. Test chamber consist of a axial mixing fan for proper mixing of gaseous product inside the test chamber, it is controllable through control panel given with the apparatus.

Product Details:

A flame test manikin is a device used for testing the flammability of fabrics and other materials. It consists of a human-shaped dummy made of material that is designed to simulate the thermal properties of human skin and flesh. To perform a flame test, a small sample of the material being tested is exposed to a flame for a specified period of time. The manikin is then used to measure the degree of burn injury that would be sustained by a person wearing the material under the same conditions. 

Additional Information:

• Production Capacity: 2
• Delivery Time: 180DAYS
• Packaging Details: CAREFULLY DELIVERED

Product Details:

State-of-the-art thermal manikin system combined with a high-precision water dosing systemOverview:• Male body-shape based on population data• 22-30 body zones with independent measurement of skin temperature and heat flux• Analysis of equivalent temperature, global thermal comfort indices and local sensation indices• Calculation of thermal and evaporative resistance of clothing, for the total body or selected zones

Additional Information:

• Delivery Time: 180DAYS
• Packaging Details: CAREFULLY PACKED

Product Details:

The test apparatus is used for measuring the smoke producing characteristic of plastics undercontrolled condition of combustion or decomposition,and also can be used for otherbuilding materials.

Additional Information:

• Production Capacity: 5
• Delivery Time: 30 DAYS

Product Details:

The ISO 11925-2 flammability standard by ISO is a standard by which plastic materials and furnishing materials can be classified with respect to their ability to withstand combustion. The rating of flammability given to a plastic material depends upon the response of the material to heat and flame under controlled laboratory conditions. The test results will give a good indication of the material’s acceptability with respect to flammability for a particular application. The behaviour to heat and flame of a thermoplastic depends on many factors such as the size, form, and end-use of the product, but also elements in the final application such as ease of ignition, burning rate, flame spread, fuel addition, intensity of burning, will affect the combustion response of the material.